Ethyl thiosemicarbazide intercalated organophilic calcined hydrotalcite as a potential sorbent for the removal of uranium(VI) and thorium(IV) ions from aqueous solutions

This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.     

Changes in heavy metal contents in animal feeds and manures in an intensive animal production region of China

The 360 feed and manure samples were collected from 150 animal farms in Jiangsu Province, China and analyzed for heavy metals. Concentrations of Zn and Cu in animal feeds were 15.9-2041.8 and undetected-392.1 mg/kg respectively, while Hg, As, Pb, Cd, and Cr in all feeds were below 10 mg/kg. Concentrations of Cu, Zn, and Cr in animal manures were 8.4-1726, 39.5-11379, and 1.0-1602 mg/kg respectively, while As, Cd, Hg, and Pb were 〈 10 mg/kg. The concentration of Cu, Zn, As and Cr in animal feed and manure were positively correlated （p 〈 0.001）, but the Cd, Hg, and Pb were not statistically correlated between the feed and the manure. Concentrations of Cu and Zn were highest in pig feed and manure, followed by poultry and dairy feeds and manures. During 1990- 2008, Cu, Zn, As, Cr, Cd contents increased by 771%, 410%, 420%, 220%, and 63% in pig manure, 212%, 95%, 200%, 791%, and -63% in dairy manure, and 181%, 197%, 1500%, 261, and 196% in poultry manure. Most of the increases occurred from 2002 to 2008, which reflects the extensive use of feed additives after 2002. In contrast, Pb and Hg in manures continuously decreased from 1990 to 2008. The results suggest that the heavy metal contents in animal manure have been greatly increased over 18 years and the contribution of manures to soil should be considered.     

Warm forming die design,part I: Experimental validation of a novel thermal finite element modeling code

Finite element analysis (FEA) has become an invaluable tool in the design of sheet metal stamping dies and processes. FEA has gained widespread acceptance as the best method of optimizing dies for conventional stamping processes. More recently, FEA has been shown to be an effective method of designing tooling for sheet forming processes. In this work, an FEA based approach is applied to the warm stamping (warm forming) process. This work introduces a new thermal finite element analysis software called PASSAGE®/Forming (PASSAGE) that enables the up-front design of the thermal management of warm forming dies. This thermal finite element analysis software is designed to specifically handle the forming and optimization scenarios related to the heating of a stamping die while minimizing user interface time. In this work, PASSAGE has been applied to a simple block of steel embedded with cartridge heaters to validate the prediction capability of this software under two different heating conditions. The results show that PASSAGE is capable of predicting the actual steady-state temperature distribution within the block with an acceptable level of accuracy while yielding notable information to the user with respect to specifying power requirements. A finite element software package like PASSAGE is a valuable tool that will aid greatly in the implementation of warm forming as a manufacturing process beyond the scope of the laboratory and into production.     

Shear cutting and counter shear cutting of sandwich materials

New lightweight sandwich materials challenge existing forming processes as well as following process steps. As such the manufacturing potential of shear cutting has to be evaluated. Two cutting methods are compared. Method commonly used is shear-cutting within one stroke engaged, the other one is known as counter-shear cutting, which uses two strokes.The challenges of cutting sandwich materials are variation of hole diameter within the different layers, fraying of the textiles, deformation of the hole contour and burr formation. These effects occur in conventional shear cutting as the intermediate layer and the lower sheet metal are cut by the scrap of the upper sheet instead of the cutting punch.The following methodology included shear cutting with closed cutting edge i.e. cutting of holes into five different sandwich materials. The sandwiches exemplarily represent multiple kinds of possible material designs. For instance, aluminum and steel face sheets, different thicknesses of intermediate layers and different intermediate layers materials such as integrated textile fibers have been used. Adequate cutting parameters such as die clearance and the use of a blank holder have been determined. To achieve good results a stiff machine design with good guidance and precise control of punch position was crucial.Observations of conventional shear cutting revealed the need of small cutting clearance of 4%. High burnish area is possible for the upper face sheet due to the superimposed force by the lower face sheet. The major conclusion depicted that high cutting quality of sandwich materials requires counter shear cutting. Hence, the roll-over of the lower sheet facing the intermediate layer, the burnish area at the lower sheet, good cutting quality of the fibers improve significantly and burr formation is avoided completely. Summarized this paper provides cutting parameters for sandwich materials based on experimental work.     

Resistance mash welding for joining of copper conductors for electric motors

The automotive industry is developing designs and manufacturing processes for a new generation of electric motors intended for use in hybrid and electric vehicles. This paper is focused on using solid-state welding to join rectangular wires in the fabrication of motor stators. Resistance welding has not typically been applied to copper due to its very high electrical conductivity; however through optimization of the current and pressure profiles, excellent quality copper-to-copper joints have been demonstrated with a technique known as resistance mash welding. A better understanding of resistance mash welding characteristics will help advancements in its application for stators. The limitations of this application will be discussed.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Presence of Torque Teno Virus (TTV) in Tap Water in Public Schools from Southern Brazil

Torque teno virus (TTV) was surveyed in tap water collected in schools from three municipalities located in the south of Brazil. TTV genomes were found in 11.7 % (4/34) of the samples. TTV DNA was detected in 10.5 % (2/19) of the samples collected at the city of Caxias do Sul and in 25 % (2/8) of the samples from Pelotas. Those cities have a low rate of sewage treatment. All samples from Santa Cruz do Sul, which has nearly 92 % of its sewage treated, were negative. These results suggest that the amount of sewage treated may have an effect on the detection rates of TTV DNA in drinking water in a given urban area, showing a mild negative correlation (r = ?0.76), when comparing the percentage of sewage treatment to the detection of TTV genomes. The detection rate of TTV was also compared with Escherichia coli, showing a strong correlation (r = 0.97), indicating that TTV may be a suitable marker of fecal contamination.     

Dimensional analysis and scaling in mechanical mixing for fabrication of metal matrix nanocomposites

For a successful enhancement of mechanical properties of metal matrix nanocomposites, a homogeneous nanoparticle dispersion and distribution in the solidified metal is required. Mechanical mixing can be used for initial break-up of agglomerates, and its study can be simplified with dimensional analysis. Using this technique, mixing time and vortex height were assessed while varying fluid properties, impeller angle, and angular speed. Three relevant dimensionless numbers were recognized: the Reynolds (Re), Froude and Galilei (Ga) numbers. Based on blade and impeller shaft angles, a modified Froude number (Fr*) was defined. These parameters were calculated experimentally, varying angular speed from 200 to 1000 rpm for three different impeller angles: 0°, 15° and 30°. This procedure was performed with three fluids: water, and two aqueous glycerin solutions (25% and 50% by volume). Digital images were taken and processed to measure vortex height. Mixing time was measured for water at 0° impeller angle, angular speed ranging from 200 to 1200 rpm. Results showed an optimal dimensionless mixing time with respect to Re. A linear relationship was found between dimensionless vortex height and Fr*. The first had a second order polynomial relationship with the product ReFr*, regardless of impeller angle. This relationship, together with the Ga, specific for each fluid, allows scaling the results to other fluids such as molten pure aluminum. This study allows experimenting in simpler systems that involve transparent fluids, room temperature and low cost, to then elaborate a prediction of vortex height in fluids where measurements are difficult and costly, such as molten metals.     

Influence of overlap between the laser beam tracks on surface quality in laser polishing of AISI H13 tool steel

Polishing by laser beam radiation is a novel manufacturing process to modify the initial surface topography in order to achieve a desired level of surface finish. The performance of laser polishing (LP) is determined by an optimum combination of several key process parameters. In this regard, the overlap between two successive laser beam tracks is one of the important LP process parameters, which has a significant effect over the final surface quality. In the current study, influence of overlap between the laser beam tracks on surface quality was experimentally investigated during the laser polishing of AISI H13 tool steel. Surface areas were polished by using four different overlap percentages (e.g. 80%, 90%, 95%, and 97.5%) while applying the same energy density. The improvement of surface quality was estimated through the analysis of line profiling surface roughness R_a, areal topography surface roughness S_a, and material ratio function. Also, individual components of the surface quality, e.g. waviness and roughness, and their evolution during LP were statistically analyzed using the power spectral density and the transfer functions. Finally, as an example of the best achieved LP result, flat surface area was polished using optimum set of the process parameters improving surface quality by 86.7% through the reduction of an areal topography surface roughness S_a from 1.35 μm to 0.18 μm.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.